Built-in ESD Protection for RFID Tag ICs

DING Yi; HU Jianguo; DUAN Zhikui; WANG Deming; DING Yanyu; TAN Hongzhou

doi:10.1049/cje.2016.06.013

Volume 25 Issue 6

Turn off MathJax

Article Contents

Article Navigation > Chinese Journal of Electronics > 2016 > 25(6): 1058-1062

DING Yi, HU Jianguo, DUAN Zhikui, WANG Deming, DING Yanyu, TAN Hongzhou. Built-in ESD Protection for RFID Tag ICs[J]. Chinese Journal of Electronics, 2016, 25(6): 1058-1062. doi: 10.1049/cje.2016.06.013

Citation:

DING Yi, HU Jianguo, DUAN Zhikui, WANG Deming, DING Yanyu, TAN Hongzhou. Built-in ESD Protection for RFID Tag ICs[J]. Chinese Journal of Electronics, 2016, 25(6): 1058-1062. doi: 10.1049/cje.2016.06.013

Citation:

PDF( 1036 KB)

Built-in ESD Protection for RFID Tag ICs

doi: 10.1049/cje.2016.06.013

School of Information Science and Technology, Sun Yat-sen University, Guangzhou 510006, China

Funds: This work is supported by National Natural Science Foundation of China (No.61402546).

Received Date: 2014-09-16
Rev Recd Date: 2015-01-17
Publish Date: 2016-11-10

Abstract

Abstract

The built-in Electro-Static discharge (ESD) protection circuits for Radio frequency identification (RFID) tag ICs are proposed. The ESD protection function is built into the rectifier and amplitude limiter. The rectifier and limiter are connected directly to the RF interface, and some transistors can discharge the larger current. These transistors can be used to build ESD protection circuits, through the redesign and optimization. The built-in ESD protection circuits can improve the ESD protection level and reduce the layout area. The circuits have been fabricated in 0.18μm CMOS process. The test results show that the built-in ESD protection circuits work well under 4kV ESD pressure and save as much as 72% of the layout area compare with foundry standard ESD protection cells.
- ESD protection,
- Built-in,
- RFID tag

FullText(HTML)

References(16)

References

K. Finkenzeller, RFID handbook: Fundamentals and Applications in Contactless Smart Cards and Identification (Second Edition). John Wiley & Sons, 2003, pp.294

Hu Jianguo and Wu Shangzhi, "Low-power energy supply circuit for passive RFID transponder", 2009 IEEE International Conference on RFID, Orlando, FL, pp.1-6, 2009.

J.W. Lee, D.H.T. Vo, Q.H. Huynh, et al., "A fully integrated HF-band passive RFID tag IC using 0.18-CMOS technology for low-cost security applications", IEEE Transactions on Industrial Electronics, Vol.58, No.6, pp.2531-2540, 2011.

G.K. Balachandran and R.E. Barnett, "A 110 nA voltage regulator system with dynamic bandwidth boosting for RFID systems", IEEE Journal of Solid-State Circuits, Vol.41, No.9, pp.2019-2028, 2006.

V. Pillai, H. Heinrich, D. Dieska, P.V. Nikitin, R. Martinez, K.V.S. Rao, "An ultra-low-power long range battery/passive RFID tag for UHF and microwave bands with a current consumption of 700nA at 1.5V", IEEE Transactions on Circuits and Systems I: Regular Papers, Vol.54, No.7, pp.1500-1512, 2007.

W. Daoxun, J. Lingli, F. Hang, et al., "Analysis on the positive dependence of channel length on ESD failure current of a GGNMOS in a 5V CMOS", Journal of Semiconductors, Vol.34, No.2, pp.024004-5, 2013.

P. Hongwei, L. Siyang, S. Weifeng, "A novel latch-up free SCRLDMOS with high holding voltage for a power-rail ESD clamp", Journal of Semiconductors, Vol.34, No.1, pp.014007-5, 2013.

F. Hang, J. Lingli, Z. Bo, "A novel ESD protection structure for output pads", Journal of Semiconductors, Vol.34, No.11, pp.114016-4, 2013.

M.K. Khaw, et al., "Implementation of internal mixed signal ESD protection onto RFID transponder IC", IEEE International Conference on Semiconductor Electronics, Kuala Lumpur, pp.901-905, 2006.

Ming-Hsien Tsai, et al., "An analog front-end circuit with dualdirectional SCR ESD protection for UHF-band passive RFID tag", 2011 IEEE International Conference on RFID, Orlando, FL, pp.142-145, 2011.

A. Boni, A. Facen, M. Bigi, "Multi-function ESD protection circuit for UHF RFID devices in CMOS technology", Electronics Letters, Vol.49, No.7, pp.453-455, 2013.

G. San Martin, P. Julian, P. Mandolesi, S. Martin, "RFID frontend in 0.5μm standard CMOS process: Experimental results", 2008 Argentine School of Micro-Nanoelectronics, Technology and Applications, Buenos Aires, Argentina, pp.126-129, 2008.

A. Wang, X. Guan, S. Fan, et al., "ESD-protected power amplifier design in CMOS for highly reliable RF ICs", IEEE Transactions on Industrial Electronics, Vol.58, No.7, pp.2736-2743, 2011.

S.H. Chen, M.D. Ker, H.P. Hung, "Active ESD protection design for interface circuits between separated power domains against cross-power-domain ESD stresses", IEEE Transactions on Device and Materials Reliability, Vol.8, No.3, pp.549-560, 2008.

M.D. Ker, C.H. Chuang, W.Y. Lo, "ESD implantations for onchip ESD protection with layout consideration in 0.18-μm salicided CMOS technology", IEEE Transactions on Semiconductor Manufacturing, Vol.18, No.2, pp.328-337, 2005.

M. Scholz, Shih-Hung Chen, S. Thijs, D. Linten et al., "Systemlevel ESD protection design using On-wafer characterization and transient simulations", IEEE Transactions on Device and Materials Reliability, Vol.14, No.1, pp.104-111, 2014.

Relative Articles

Supplements(0)

Cited By

Proportional views